Revell 1/32 Typhoon 1B with car door canopy (Build)

[rtfoe]

Hi Everyone,

Here's Henry Talalla's Typhoon or near enough as he may have been shot down in a later bubble four bladed version of the rocket firing Typhoon. It is in his squadron markings, 182Sqd. The car door version was being switched just before D-Day with the upgraded bubbled canopy version and since only the CO has a constant aircraft of his own, the others would fly in anything operational and assigned to them on that day. I'm pretty sure Henry would have flown the car door version or the B1 when joining his squadron.

The kit is a Revell 1/32 scale with raised panel lines and covered with rivets. These all had to be sanded down and panel lines re-scribed. Early on I had decided I would not show the engine but one was provided that can be super detailed if one so chooses. Also I wanted to correct the wheel wells.

[ATTACH]315927[/ATTACH]

I just painted the engine black and hoped it wasn't visible in any openings. The kit wheel well sides were molded flush with the contours of the door flap. But in reality it was boxed shaped on the inside.

[ATTACH]315928[/ATTACH]

I cut away one side and proceeded to cut the other along the edge of the well.

[ATTACH]315929[/ATTACH]

Meanwhile I thought the flaps ought to shown open as well...living dangerously was I...so cut away I did.

[ATTACH]315930[/ATTACH]

Whatever was cut was replaced with plastic card...

[ATTACH]315931[/ATTACH]

Everything was mirrored for the other side....

[ATTACH]315932[/ATTACH]

The rivet impressions hide the rscribed panel lines. The kit was peppered with it...very measled like.

[ATTACH]315933[/ATTACH]

From the inside it looked like this. The boxed frames held everything in place inside the well. This also shows how thick and robust the Typhoon wings were.

[ATTACH]315934[/ATTACH]

More later...

Cheers,
Richard

[rtfoe]

Here's more of the wheel well construction. I needed to replicate piping and servo units in the well and I found resistors that looked like them.

[ATTACH]316039[/ATTACH][ATTACH]316040[/ATTACH]

With as much reference that I could find I made the well look as busy as it could be.

[ATTACH]316041[/ATTACH][ATTACH]316043[/ATTACH][ATTACH]316044[/ATTACH]

With some paint and weathering it looked a bit better but if I had known then that I do now is that wheel wells on Typhoons were silver in colour. Well I could remask and do it all over again but it's too much trouble...perhaps one day. So far no one has looked under.

[ATTACH]316045[/ATTACH]

Lots of puttying to the joints coming up.

Cheers,
Richard

[Jim R]

Hi Richard
Another rather poor kit getting the RF treatment. The wheel wells look great. Just sanding and rescribing a couple of panel lines is time consuming but tackling all of them - that's dedication.
Jim

[Steve Jones]

Nice tip with the resistors. I hope the electrics in your house still work.:smiling5: Stunning work as always:thumb2:

[rtfoe]

Thanks Jim and Steve for commenting. Well the kit was sitting around on the shelf and I had spare time plus it was theraputic. Even with three faced wire ring it's been tripping quite often during thunderstorms and I had nothing to do with it...I'm scared stiff at touching any wires in the house.

The Typhoon had very large barn door flaps which I wanted to show dropped. Unfortunately they were molded shut so I cut it and created the individual frame with pre drilled card and rod styrene. Here are the flaps...

[ATTACH]316390[/ATTACH]

Obviously when anything is cut away gaps need to be filled or blocked...

[ATTACH]316395[/ATTACH]
[ATTACH]316396[/ATTACH]

And sanded...

[ATTACH]316397[/ATTACH]
[ATTACH]316391[/ATTACH]

Test fitted...

[ATTACH]316392[/ATTACH]

Painted and weathered....

[ATTACH]316393[/ATTACH]

I painted the reverse side black as the cockpit came in a turbular frame that you could see right through to the bottom.

[ATTACH]316394[/ATTACH]

Cheers,
Richard

[rtfoe]

Hi Ya'll,
Now we're moving onto the fuselage. The side walls were practically devoid of any ribbing frames so I made some up with plastic strips. I based the measurement of the sections on the rivet detail on the outer fuselage.
[ATTACH]316702[/ATTACH]

The firewall was attached to the engine so that had to be installed. As mentioned, the engine would be a nice piece to detail but I wasn't intending to so its just painted in black.

[ATTACH]316703[/ATTACH][ATTACH]316704[/ATTACH]

I created more detail to the left door panel

[ATTACH]316705[/ATTACH]

The right fuselage ribbing and frame was duplicated...the difference was that the door is in the opened position.

[ATTACH]316706[/ATTACH]

Attention was paid to the door panelling. The two raised injector pin marks were being removed with a sharp blade...one has already been sliced off.

[ATTACH]316707[/ATTACH]

If you wanna see more check out the next posting.

Cheers,
Richard

[rtfoe]

Here's more to the interior but real bad pictures. The camera keeps focusing the foreground.

The kit comes with a flat instrument panel to stick a large piece of decal. I photocopied the decal and using that as a template, I cut out panels and drilled bezels for the instruments. I did the usual sandwiching of decal and panels to the kit instrument panel. The side consoles were also enhanced with knobs and a raised compass. I painted the facings carefully in black and dropped Future into the drilled out bezels to create glass covers for the instruments.

[ATTACH]317145[/ATTACH][ATTACH]317146[/ATTACH][ATTACH]317147[/ATTACH]

The kit seat was flat at the bottom so I cut that out and created a bucket. This is where the parachute normally fits and the pilot sits on it. I also kneaded up a back cussion.

[ATTACH]317150[/ATTACH]

The seat was attached to the back armour plate and the floor had enough room for the bucket extension. Fixed on the gun sight, joystick and pedals. I didn't have enough reference to tell if the seats were made from the same material as the Spitfire seats so I left it in interior green.

[ATTACH]317148[/ATTACH]

All the parts are left unglued for easy painting and re-attaching.

Cheers,
Richard

[Steven000]

Great to see all of the new details you're adding to this model Richard .
Those resistors look nice too in the well...
Cheers, Steven

[Guest]

Hi that's a masteclass in scratch building Richard, very crip and clean :thumb2::thumb2::thumb2:.
Old Puffer Pete.

[rtfoe]

Thank you Steven and Pete. Apparently sources say that the kit is pretty accurate in surface detail for an old model. All it needed were the few extras to ham it up.

Cheers,
Richard

[rtfoe]

Get ready for more pictures of the cockpit after some painting. A few more bits and bobs like circuit boxes and knobs were added.

[ATTACH]317505[/ATTACH]

The leather back cushion recieved a coat of red brown. Dark washes and lighter shades of brown were later painted on.

[ATTACH]317506[/ATTACH][ATTACH]317507[/ATTACH][ATTACH]317508[/ATTACH]

My usual seat belts out of masking tape were attached with some CA glue and the whole assembly weathered with washes and painted highlights.

[ATTACH]317509[/ATTACH]

Dials and switches were picked out with white and red...finally the dash board can be seen clearly.

[ATTACH]317510[/ATTACH][ATTACH]317511[/ATTACH][ATTACH]317512[/ATTACH][ATTACH]317513[/ATTACH]

Bit by bit the dark wash and highlights with drybrushing brought the canopy to life.

[ATTACH]317514[/ATTACH]

There is still the seam line I missed on the gun sight. The camera can always pick up these details on close up. Filler can be seen just ahead of the cockpit to fill a dimple.

[ATTACH]317515[/ATTACH]

Soon I'll close the fuselage.

Cheers,
Richard

[rtfoe]

After all innards were completed, the basic closing of the main parts that make up the aircrafts body, wings and tail is done. You can see visible the scribbed panel lines on the aircrafts surface. The kit fit was pretty good for an old mold. There were gaps for the engine panel that was given to expose the enging if one wanted to.

[ATTACH]318691[/ATTACH]

The wing roots fit so well that minimal filler was needed only for dimples at attachment points seen here just forward of the cockpit.

[ATTACH]318692[/ATTACH]

Thanks for looking in.

Cheers,
Richard

[scottie3158]

Hi Richard,
Missed this up to know but the magic is already showing great work so far.

[AlanG]

Bit late to this build myself but a fantastic read none the less. Loving your scratch building

[rtfoe]

Hey thanks guys, no worries as posts get shifted down the pecking order quite quickly here and can be missed.

The Typhoon is one of the least featured planes but is getting some coverage lately at D-Day reunions. Little known fact that they slowed down German reaction for counter attacks hitting ground targets trying to reach the beach that many thought was Hitlers reluctance to deploy his forces. No doubt the main heavy armour was kept to the North there were elements of Rommels make shift defence armour that were decimated everytime they came out of cover by aerial bomb or rocket attacks by fighter bombers like the Typhoon. Only well concealed anti-tank guns or small tank company's travelling by night hindered the Allied advance. Any large German columns in daylight on roads were sitting ducks for allied fighter bombers.

Cheers,
Richard