The one thing about models I don't like: Seams!

[SUBSIM]

I hate seams, especially the long seams like the sections of hull where no seam should be. I've watched a ton of videos on how to eliminate seams. I've tried AK grey putty, Tamiya white putty, Tamiya Liquid Surface Primer, and adding super thin cement to flush the two surfaces. Still, after I add a coat of primer, there's the seam.

With the puttys, even when I add a tiny bead with a toothpick, when I try to sand and feather it out, it doesn't help, plus it's hard on the fine details.

How many hours should I spend on a model trying to putty and sand the seams?

[spanner570]

To be honest Neil. I don't bother doing anything special with my ship/ boat seams. So my answer to your question would be virtually nothing extra, rather poor I realise, but that is my method of modelling. The easy life!

I always cut off the lower hull and sling it. Then once my stuff is 'afloat' and weathered, the seams are invisible. Well, near enough for me.

Of course the 'Zoom Merchants' would have a field day, but guess what?......

Ron

[Guest]

I don’t build many boats (could leave the m out of that, really) but I normally fill seams with car body putty, and make sure that the filler is proud of the seam. Once that’s thoroughly dried, I sand it down with wet-and-dry sandpaper (used wet, that is) until I can’t feel the seam anymore with my fingertips and -nails. After that, it’s almost always invisible after painting; if not, then a little more sanding, some more filler and sanding again normally does get rid of it.

As you say, though, this can be difficult with details near the seam. My only advice here is to be careful, and realise that you can’t really avoid all damage, so accept that you may have to rescribe panel lines and/or rebuild details from scratch. It may help to carefully slice off raised detail if it’s big enough, then glue it back once the seam is filled to your satisfaction.

[Dave Ward]

Neal,
first thing I do when joining sub hulls is edge preparation! I scrape the sharp edge away from either side of the hull, removing the 'corner' of the jointing faces, using a scalpel blade - this reduces any ridge where the two parts meet. If there's a serious mismatch, I'll deal with it, by filler, or inserts of plastic card before attempting a joint. I run a thin bead of Contacta glue around each half of the hull, and allow to dry for 4-5 minutes, then press firmly together, using tape or clamps to maintain the pressure - the glue should have softened the plastic enough for a thin ridge of plastic to be pressed out of the join. You have to leave this for at least 24hrs to really go off. The extrusion can now be trimmed off with a new scalpel blade - if you do it right, no more treatment required, otherwise w&d paper used wet.
It is a long time since I did this, however - waterlining is my choice these days!
Dave

[Ian M]

Large parts be it a hull or fuselage I find best to use a poly glue with a bit of body to it.
Plenty of it too! The resulting ouze of glue once dried and hard can be trimmed off and a gentle sanding should do the trick.

[Jim R]

Many long joins are along a curve, especially true for plane fuselages. I find it very easy to sand a 'flat' when trying to sand out the seam. I have one of those IPMS curve scrapers but even that has limitations.
Jim

[Gern]

Make sure you've got plenty of glue/cement in the joint before fixing the parts together. If there's any part of the join which is not fixed together, you'll ALWAYS have a gap between the two pieces of plastic.

[SUBSIM]

Lot of great suggestions. Here I was thinking Tamiya super thin was the greatest thing since sliced bread, being able to brush it on parts that are already placed together.

Large parts be it a hull or fuselage I find best to use a poly glue with a bit of body to it.
Plenty of it too! The resulting ouze of glue once dried and hard can be trimmed off and a gentle sanding should do the trick.

What poly glue do you recommend? In my last session of model building (the 2000s) I was quite excited to use MM with their awesomely precise needle. I looked for that but now it seems it is Testors and the metal needle is gone. :confounded:

[SUBSIM]

I meant, what poly glue.

Seems like I cannot edit my typo....

hah, now I can

[Ian M]

Yes thats the type of stuff. I normally have either Humbrol or Revell as that is what I can get.
Also a big user of the thin glue. Normally Tamiya extra thin, but I am trying the MIG stuff.

[Tim Marlow]

Revell Contacta professional will work well on those type of seams Neal. It has the metal needle applicator as well. Tamiya extra thin (or other liquid solvents, there are several) is great for other types of joint. It’s worth having more than one sort of poly glue for different applications.

[Dave Ward]

For delicate parts, TET is ideal, but for anything larger

You can get it in 12.5 or 25 g bottles I always have several in hand - it's my go to cement - I would say 75% of a model would be assembled using this. + it doesn't spill if you knock it over!
Dave

[SUBSIM]

Revell Contacta professional will work well on those type of seams Neal. It has the metal needle applicator as well. Tamiya extra thin (or other liquid solvents, there are several) is great for other types of joint. It’s worth having more than one sort of poly glue for different applications.

Beautiful, thanks!

[Guest]

Not sure if you can easily get that glue in the USA, though — it’s a Revell Germany product only, as far as I know. But I could be wrong

[Tim Marlow]

Good point Jakko. Amazon.com has it, but it ain’t cheap…bit like trying to get Tamiya grey putty in the uk by the sound of it.