How do you wash a big cat?

[rickoshea52]

In preparation for building the Airfix 1/24 Hellcat I need to start with washing off any release agent or other surface contaminants. Now, if you’re not familiar with this kit the sprues are massive. So while the kitchen sink might be acceptable for the kids (that’s where I had a bath as a child) it just won’t accommodate this big cat.
Time for the big bath, some fairy liquid and a soft brush.
Everyone knows to wash the plastic before building a kit so what’s my quick tip? I have this redundant IKEA dish rack which just happens to be perfect for drying the sprues after a wash. I’ll also use it as a sprue rack when the build starts.
The other tip is you can save time and soap if you chuck the kids in too.

[ATTACH]444135[/ATTACH][ATTACH]444136[/ATTACH][ATTACH]444137[/ATTACH]

[yak face]

Thats a lot of sprues rick! Good job its a big drying rack .

[Tim Marlow]

Now that’s a big cat. Keeping the plug in would seem imperative as well Rick

[Tworrs]

Goodness me that is a lot of sprue, I like idea of using the Ikea rack for holding the sprues whilst building, I always have every surface covered in them.
Great idea, thanks.
Garry

[Jim R]

Hi Rick
Definitely a lot of sprues. Rack looks a great idea.
Jim

[BattleshipBob]

Thought if i read this i could try washing my big cat, casper

But alas no!

[JR]

Rick.
Great use for the redundant rack, there will now be a rush on to get one:smiling3:

[Ian M]

Oh! that kind of cat.
I was going to say I normally turn the shower on full blast then throw the cat in the shower cabin,
I'll get my coat.

[arb65912]

I need to start with washing off any release agent or other surface contaminants.

What soap should be used? And in what concentration?
I am a total newbie, so I did not wash it. :flushed:

I can do it now, but some parts are glued together (elevator halves for example) and there is a hole so water can get inside while washing. How do I make sure there is no water left after the drying?

[Tim Marlow]

What soap should be used? And in what concentration?
I am a total newbie, so I did not wash it. :flushed:

I can do it now, but some parts are glued together (elevator halves for example) and there is a hole so water can get inside while washing. How do I make sure there is no water left after the drying?

Not a huge problem, some people don’t wash them at all. I like to, especially if I’m using acrylic paint, but if you are using enamel or lacquer paint its not essential. You can just wash it when it’s built, by the way, and before you try to paint it Andrzej.
Normal dish washing soap used at the same concentration you use for your household washing up will be fine. Cold water is best though. Plastic can distort in hot water.
If water can get in, it can also get out…..if you are worried about getting the water out, don’t immerse the model, just wipe the surface down with a sponge and rinse it the same way…

[stillp]

You could just wipe it down with alcohol and a tissue.
Pete

[colin m]

I am a total newbie, so I did not wash it.

I don't wash my sprues unless I can see or feel anything suspicious.

[Ian M]

You could just wipe it down with alcohol and a tissue.
Pete

Just make sure the alcohol is not to strong. Even IPA can mark plastic if very high concentration.

[outrunner]

Just do whatever you think, I have never washed kit spues before building and had no problems, perhaps I am just lucky?

Andy.

[arb65912]

Just make sure the alcohol is not to strong. Even IPA can mark plastic if very high concentration.

IPA you mean Isopropyl Alcohol? How about 70%?