boatman's 1/72 HMS Tiger C20 build

[boatman]

Chris, I'm surprised you didn't power that tail rotor through contacts in the hinge area instead of wires, so when the tail is folded the contact is broken so the rotor isn't powered.
Pete


ps I'm only joking! :tongue-out:

WOW Pete :thinking: dont do that give me ideas like that you'll give me a heart attack lol you must have seen how small the area is with your chopper LOL but i think that idea has merit on something a bit bigger with contactacts on a non eletrical back plate an same on the other side of the hinge so that when you close it the eletric passes an works thing an when the hinge is swung back then the eletric contact are broken congrates Pete a very good idea indeed an i may use it someday hope you not goin to pattern pending the idea :tongue-out3: :rolling: :smiling: :cold-sweat: lol
chrisb

[stillp]

Yes Chris, you'll have to pay me royalties! :smiling5:
Pete

[boatman]

Yes Chris, you'll have to pay me royalties! :smiling5:
Pete

OH Pete you Rotter you CHARGEIN an ole m8 whom youve known for yrs lol
chris b

[stillp]

Don't worry Chris, I'll give you a good discount.
Pete

[boatman]

Don't worry Chris, I'll give you a good discount.
Pete

DISCOUNT Pete well as long as its 100 % i'll be happy lol
chrisb

[stillp]

It'll be a nice round figure Chris.
Pete

[boatman]

It'll be a nice round figure Chris.
Pete

what like 0 ? thats a nice round figure lol

[boatman]

HI Pete did you have any trouble with fitting the glass in as mine is terrible ive had to file off a mm of glass to get the side windows to fit :crying:
chrisb

[stillp]

HI Pete did you have any trouble with fitting the glass in as mine is terrible ive had to file off a mm of glass to get the side windows to fit :crying:
chrisb

The side windows were fine Chris, except where I'd opened up the hole in the fuselage a bit too much - this SAR versions has more side windows than the transport ones, so the kit needs the holes cut out for some of the windows. The canopy fitted perfectly, but the panel under the front of the canopy needed a bit of sanding.

If you were thinking of doing another Sea King I can recommend the Revell kit.

Pete

[boatman]

The side windows were fine Chris, except where I'd opened up the hole in the fuselage a bit too much - this SAR versions has more side windows than the transport ones, so the kit needs the holes cut out for some of the windows. The canopy fitted perfectly, but the panel under the front of the canopy needed a bit of sanding.

If you were thinking of doing another Sea King I can recommend the Revell kit.

Pete

WELL Pete ive got another brand new kit that i had forgotten i had an i could kick myself as this is a airfix kit an it has the motor mounting already built in by airfix but me bein a forgetfull dumbo dint look in the cuboards till i bought the one im now workin on an i coul have saved myself all that measuering to fit the main motor but whats done is done an in some ways this kit is a better one even though a rotten fit as its got the bottom seperate so i can jion up the two sides but still get into the fusalarge an all togeather ive got to build 4 seakings but i was lucky that andy the paint guy who used to be on here dint like the yellow finish on his raf seaking so he sent it to me to use on tigers flight deck so i dont need to buy any more thank goodness as its getting costly an cheers for the info on the glass fits
ATB
chrisb

[boatman]

HI ALL again still on that chopper as a few more pics to show whats happening on it an fitted in the floor an to see how it fits an not very well im afraid i thought dragon kits were good but this one is oop:

[boatman]

more wires an lights

[boatman]

an here a shot of the wires caseing that will slide up an down in the fusalarge to allow the tail section to swing back an fourth in red

[Mini Me]

Looks like you're making progress though...

[boatman]

an in the rear fusalarge 3 winch men sit waiting