Is it just me...

[Guest]

Sorry Gents had to scroll through 90% of posts on subject maybe NOT my best day, but my advice.... buy the cheapest crap paint you possibly can and hit it like Picasso with a vengeance. Seems to work for me, let the true 3D artist in you come out and don't entangle yourself in technicalities. If I'm out of line then just ignore me {as most do} hate to see the FUN lost! Have a good tipper and ENJOY yourself that's what it's all about I feel. Never did like those little spitting devils but maybe that's just me. CHEERS! JIM

Right-tee-ho Jim


Laurie

[Guest]

I find it strange that you should get problems with the paint. Some of mine is now five years old including the primer.
All works perfectly. If you are using a .4 nozzle which I have on an H and S then there should not be any problem even a little lump will go through that.


So Steve I do not think it is your paint. I think there is a problem with your airbrush. Your paint worked before you have had this recent problem and presumably you have tried other colours to ensure you are not using a rogue. As the worms do not issue form the paint pot then they are forming in the airbrush and the question is why.


Assuming all of that as being so then it is an airbrush problem. Not mentioned anything about seals. I would change your seals while changing the nozzle. Also while at it change the needle if it has a slight bent top of a small curl on the top it will ruin the nozzle and could be a likely contender for the "worms".


I always keep a spare needle/nozzle set. When things do go wrong it is easy then to eliminate a problem with needle/nozzle by swapping.


When you clean Steve do you brush back up from the front end of the brush up through into the cup. Also from the spring end down through to the front nozzle end. That needle housing tunnel does get paint backed up into it. If it is not cleaned properly old paint will come back down, as bits into the nozzle area, as it is loosened by the thinners in the new paint being used.


Laurie

I have established (I think) with the help of Everything Airbrush and others including you (many thanks) that the nozzle has got blocked gradually over time, despite my very rigorous cleaning. As Ian M said, using Tamiya Lacquer and its solvent Cellulose thinners for a couple of months before I put my AB away for a few months could have caused the thinners remaining to react with the following Acrylic paint. So the acrylic paint was probably not the problem, but until I return to normal I will decant paint for a short time to confirm success. As Ian M said, when something mysterious is happening it is important to exclude as many things which might contribute to the problem.


On cleaning from the nozzle end to the trigger, I brush this with cleaner every time. However, I am not clear whether it is wise to push that little bottle brush through the seal in the middle of the AB. I need to check that.


I have ordered a new nozzle and the nozzle cleaning kit.

[grumpa]

Wow! I could have completed two projects and a case of pints plus snookered the ;;


Mrs. a few times by then Love that word 'snookered' Have given it my own YANK meaning DON'T CHA KNOW!

[Guest]

.......Actually if you have a magnifier light Steve place under the magnifier large end upwards and look through. You will soon locate any residue of paint. With a .4 it is easy not so with a .2. You will see, if clean a lovely round hole.
..........

I forgot to reply to this. After every clean I always look through the nozzle (from the inlet end of course—the tiny outlet is too small to see through) against the sky which seems better than a light, and always checked that the outlet appeared as a clean round hole. Also, by changing the angle of the light entering the nozzle I checked that the part nearer the entrance reflected as shiny, and by rotating the nozzle about its axis I checked that nothing could be seen rotating with the nozzle, just shiny reflections. Belt and braces! But none of this prevented the blockages that I have been having.


I bought the reamer and a spare nozzle. On using the reamer I did not see any crud on it which I was hoping for. On further cleaning of the nozzle, I got a blockage when using one of the paint bottles that I had inspected for lumps by pouring into a jar and back again (as mentioned in my earlier posts). I changed to the new nozzle and was able to spray covering a surface larger than an A4 sheet and which was for about 15 seconds. I repeated this successfully with another colour of paint. So, fingers crossed!


When John's Vallejo Airbrush Flow Improver arrives I plan to use that every time.